Chưa có sản phẩm trong giỏ hàng.
Chưa phân loại, Style, Uncategorized
Danh sách lỗi máy CMM Hexagon Error list – Cách khắc phục sửa chữa – Phần 4
26
Th12
Th12
Hexagon CMM là thương hiệu hàng đầu trên thế giới. Máy CMM Hexagon được sử dụng khá phổ biến tại Việt Nam.
Mstek cung cấp cho quý vị thông tin lỗi máy CMM sửa dụng bộ điều khiển: DC240/DC241 DC241ETH//DC800/DC800ETH/RC1/DC4000/H3C-T
Dưới đây là Danh sách lỗi máy CMM Hexagon Error list – Cách khắc phục sửa chữa:
AI – Axis Interface (layer 5)
| 0x15000001 | System Error calling a RTOS function |
| 0x1500?010 | Output data of previous clock not written |
| 0x1500?011 | Excessive change in position |
| 0x1500?012 | Excessive lag |
| 0x1500?013 | Overspeed |
| 0x1500?014 | PHM communication error |
| 0x1500?015 | PHM datum error during movement |
| 0x1500?016 | PHM not connected |
| 0x1500?017 | PHM control code error |
| 0x1500?018 | PHM transmission error |
| 0x1500?019 | PHM invalid data |
| 0x1500?01A | PHM datum error (not seated) |
| 0x1500?01B | PHM obstruction |
| 0x1500?01C | PHM overload |
| 0x1500?01D | General hardware error |
| 0x1500?01E | Transducer error, unknown code meaning |
| 0x1500?01F | Drive error, unknown code meaning |
AI – Axis Interface (layer 5) 0x1500002x
| 0x1500?020 | Weight Balance routine timed out after a PH rotation |
| 0x1500?021 | Drive error: IxT |
| 0x1500?022 | Drive error: voltage saturation |
| 0x1500?023 | Drive error: tacho speed too high |
| 0x1500?024 | Drive error: command refresh timeout |
| 0x1500?025 | Drive error: VP overvoltage |
| 0x1500?026 | Drive error: VP undervoltage |
| 0x1500?027 | Drive error: servodrive overtemperature |
| 0x1500?028 | Drive error: VP overcurrent |
| 0x1500?029 | Drive error: brake resistor failure |
| 0x1500?02A | Drive error: MOSFET auxiliary voltage failure |
| 0x1500?02B | Drive error: AD converter failure |
| 0x1500?02C | Drive error: invalid DSP firmware |
| 0x1500?02D | Drive error: invalid DSP params |
| 0x1500?02E | Drive error: invalid SET_PARAM command received |
| 0x1500?02F | Drive error: RAM check failed |
AI – Axis Interface (layer 5) 0x1500003x
| 0x1500?030 | Drive error: CPLD check failed |
| 0x1500?031 | Drive error: short circuit on a digital output |
| 0x1500?032 | Drive error: failure programming the transducer offset E2POT |
| 0x1500?033 | Drive error: Hardware error no Ready Pwm |
| 0x1500?034 | Drive error: signals GFAIL and READYPWM not coherent |
| 0x1500?035 | Drive error: signals NINH and POWON not coherent |
| 0x1500?036 | Drive error: signals NINH and BRKN not coherent: failure detected on KP relay |
| 0x1500?037 | Drive error: unknown event received |
| 0x1500?038 | Transducer error: TTL alarm signal detected (TRASER) |
| 0x1500?039 | Transducer error: TTL missing signal (FLET) |
| 0x1500?03A | Transducer error: edge separation |
| 0x1500?03B | Transducer error: speed mismatch |
| 0x1500?03C | Transducer error: amplitude error |
| 0x1500?03D | Transducer error: phase error |
| 0x1500?03E | HF instability |
| 0x1500?03F | Excessive dual disalignment |
AI – Axis Interface (layer 5) 0x1500004x
| 0x1500?040 | Force limitation threshold exceeded |
| 0x1500?041 | Force limitation algorithm intervention |
| 0x1500?042 | THD answer timeout error |
| 0x1500?043 | No HP-THD probe detected |
| 0x1500?044 | Invalid THD probe parameters |
| 0x1500?045 | Error during THD probe configuration |
| 0x1500?046 | Failure opening a file |
| 0x1500?047 | Error during THD controller configuration |
| 0x1500?048 | PHM firmware update required to use thdConfig parameters |
